Configuring Atmel Studio 7There are a few things you need to do make sure of once you have it installed
Jan 20, 2016 I have the Atmel SAM ICE, and installed the JLink V510o as well as the driver-atmel-bundle-7.0. I have Atmel Studio 7 running also. How do I configure this adapter to work with µVision? Install J-Link Drivers. Download and install the latest. ΜVision DEBUGGER: Atmel-SAM-ICE Debugger. ATMEL - Atmel Corp. - Atmel-ICE Data Gateway Drivers Download - Update your computer's drivers using DriverMax, the free driver update tool. Atmel-ICE User Guide. Online Catalog: ATATMEL-ICE-BASIC Debugger Product Attributes. CABLE SAM ICE. I have the Atmel SAM ICE, and installed the JLink V510o as well as the driver-atmel-bundle-7.0. I have Atmel Studio 7 running also.
M. A. Parker c2015
Installing Atmel Studio (AS) and a programmer embody the first steps [0] on the path to using an individual Atmel AVR Microcontroller unit MCU [1] as opposed to the MCU-on-a-board such as Arduino [2]. Here starts the journey, albeit rather short, through a series of ‘Startup’ Instructables [0] focusing on ‘getting started’ with the Atmel MCU. Along the way, the series (Startup 5) shows how to construct the ‘Lifeline’ to fix wrongly set fuse bits – a simplest of projects but useful to the expert and makes a nice gift. This initial Startup describes the setup of the Atmel Studio and Programmer and the construction of an adapter cable for connecting the programmer to an experimenter’s board. Startup 2 describes the construction of a ‘platform’ circuit on an experimenter’s breadboard used to set the internal fuse bits of the MCU. The circuit will be used for the remaining three Startup Instructables. Startups 3 and 4 use the platform to demonstrate ‘Blinky’, the blinking LED, and to describe the ‘secret’ life of the Atmel PORT, PIN and DDR registers and pull-up resistors.
Atmel Ice Driver Windows 10
**NOTE: For those wanting the PDF of this instructable, download the attached PDF using the below link rather than the one automatically generated by the website - that automation does not maintain the association of the captions with the pictures.
Atmel Sam-ice Driver
We began using the Atmel MCUs in the early 2000s in order to create Data Acquisition units for experiments with IC fabrication and for demonstrating a unique multichannel noise communicator. Similar to other people, we had to learn certain well published ‘secrets’ of the Atmel AVR Microcontroller including, at the most basic level, the Data Direction Register DDR, PORT versus PIN and the USART data format (inverted). Fortunately, a consulting firm supplying our MCU needs, also provided assistance for ‘getting started’ and pointers on the ‘secrets’. While planning to publish some MCU projects, it seemed reasonable to pass along the favor by providing some ‘Getting Started’ guides, although in considerably more detail, so that other interested people might benefit.
This Instructable provides an introduction to using a single Atmel MCU. Although we start with the ATTiny2313A [3], the discussion applies to the popular Atmel AVRs (8bit) such as the ATMega328p (of Arduino fame). With the single Atmel MCUs, the builder controls all the options and expends much less cash than for the larger and more expensive Arduinos [2]. The 2313A have a price of about $1 each and the budding experimenter will be much less traumatized if a couple should go up in smoke. Future articles will center on other Atmel MCUs such as the ATMega328p and the SAM line. On the other hand, the remarkable Raspberry PIs [4] run Linux with plenty of USB peripherals but uses an event driven architecture that limits real time data acquisition.
The Atmel Studio 6.2 (AS6) software provides an Integrated Development Environment (IDE) which, among other features, (i) allows the user to type programming statements, (ii) compiles the programming statements into proper MCU syntax (i.e., hex code), (iii) transfers the MCU code to a programmer usually attached to a USB port, and (iv)saves/retrieves programs from disk. AS6 will function with any of the Atmel MCUs including AVR (i.e., 8 bit) and SAM (i.e., 32bit). The programmer generates the necessary signals onto the MCU’s Serial Peripheral Interface SPI pins that engage and synchronize the MCU’s internal ‘In-System Programmer ISP’ [5]. In short, the programmer transfers the code to the MCU. Atmel Studio provides C and C++ compilers which convert programming statements into MCU syntax/Hex code.
Atmel Sam Ice
This instructable includes notes on tools toward the end and some references for the programmer. However, the majority of the reference/tutorial links for electronic components and C/C++ will be found over the next several installations of the Startup series where they will be used.
Comments are closed.
|
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |